fcd72
About
- Username
- fcd72
- Joined
- Visits
- 1,237
- Last Active
- Roles
- Member
Comments
-
Ladies,dont run havoc, dont panic. From my experience a registered letter to the U.S.of A. take something between 5-45 working days, totally independent of destination, packaging, content and/or Pandabear stickers on the Package. Actually German Pos…
-
the main reason usinr rnets is saving space, so diprnets are a bit pointless as thea are much more xpensive + dont save space or solderjoints. good solition wouls be using rnets for the buttons near the 165s an normal rs for the leds each directly n…
-
This is the usual "can i send you some drawings and you cut a case of it" problem that mist programs dont really scale 100% in each direction + the fact that my Laser's Software doesnt scale exactly 100%, too. Inkscape does an especially bad job her…
-
Sold out in 38 MInutes. Congratulations!!!
-
@sammy123 Standard Cases via the SP shop, custom cases anytime you like
-
T -57 min and counting . . .
-
As loderbast said a voltage around 7.5V (not much less as the 7805 regulator need about 2V headspace to work properly) is fine. Its just that the Cortex Processor needs loads of Power, so be prepared your 2500mA Battery pack will only last for 2-3 H…
-
@Lindeborg If you arent satisfied by the Stock case, you can eMail me anytime.....
-
... ill go order some Plexi...
-
I guess - but thats a rather wild one - if theses LXR thingies sell out quickly the creator might be tempted to do more. Maybe its not meant as a single Run Machine? ;-)
-
Please pay attention to these supercool but xtraexpensive (well, for a screw...) hex screws that hold the top panel. I made the Engravings extradeep in case anyone wants to fill them with neongreeeeeeen paint or something ;-)
-
A hub should be transparent for any kind of information and since USB is digital you either have a Signal or not. There is no "strength" of Signal besides in the physical layer....
-
I just finished cutting cases..... i clearly won ;-)
-
Will there be a Shop and a Countdown?
-
When its in your Mailbox its to late to complain ;-)
-
@dubtomsActually the Logo is a quite cool piece of Artwork from a (at least to insiders) well known Artist - i would have acted as a TasteGateTM if it was ugly claiming that it wouldnt be technically feasible otherwise ;-)
-
Im the remote troubleshooting hero ;-)
-
Keep us update - this is a viable Information for the next iteration of PCBs
-
Maybe you have a short on the USB Jack, see this Flickr Album There are 2 Pads benath the USB Jack that might cause irritations, maybe you desolder the Jack, put a piece of Tape on it (the red stuff in the Pic) and resolder it.
-
I think its more a price induced decision....
-
@cereyanlimusiki Case is done, only the Logo is lacking - and a decision for the color.
-
Having seen the mountains of Boxes over at Julians House im pretty shure there will be complete Kits......
-
@diylineMost off the LCDs + OLED i have seen have SIL connectors to the top or both Top and bottom. A 2x16 with DIL to the side is quite rare...
-
I will see what i can do with the Cardboard spacers.... ill have to desolder my screen anyway. LCDs saugen!
-
Yo Ladies,why not pool all of your ideas and talk Julian into doing a Sequencer? Its no use pimping up a dedicated DrumSynth to an Eierlegende Wollmilchsau....I guess no one of you is constantly touring round the world while carrying your Rig as MLC…
-
Oh please don't make it a Eierlegende Wollmilchsau suffering from Featuritis.....
-
I can predict the future because i own a Black Hole
-
As far is i know Julian i bet sooner or later there will be a "Transients" Folder on the SD and you just throw them in.....
-
I dont care as long its a programmer ;-) Ill be at it as soon as the Parameterset is frozen. I think a 137/595/4051 multiplexed thing would be better, freeing up the MIDI port and not adding further Delay merging the Data with the MIDI Stream. I lik…