Xirso
About
- Username
- Xirso
- Joined
- Visits
- 0
- Last Active
- Roles
- Member
Comments
-
Thanks,Your response give me a better understanding of the schematics and how to use them to follow a signal on a pcb.So, I have put some more solder on CV jack. Use a solder bread between pin 1 and 2 from the MCP602 to prevent a short between the t…
-
Thanks, good to know that the penrose is protected, that's give me hope.- The penrose receive an LFO to the CV input and the CV out of the penrose goes to an oscillator, like you write.- The led and buttons are working, i can press every button and …
-
Just two questions:"metal enclosure" like the case from Erica Synths on the LXR shop?With trigger extension?
-
" lfo with tempo/roll/time signature destination" you miss understand me, i don't think this is possible. But, retrigger the lfo on every step with some other destination and place substep, or set the lfo speed at the same sync rate as the roll, cou…
-
This parameters aren't in the midi chart, so i think it would be difficult to modulate them with an external source, and it look's like the internal modulations destinations of the LFO are the same that the parameters that you can control with midi.…
-
Wow, very nice case and print!
-
From my point of view this is a separate issue. On start up, when the LXR boot not correctly, can you use it or not? The only time i had a strange behavior from my LXR it was cause i move a bit the LXR and the power supply moved a bit too. Perhaps c…
-
I admit that i don't really understand what you are writing. Perhaps your LXR receive clock from to different source, the midi input port and the usb midi in and that cause this strange behavior. Or recheck the midi port routing options to be sure t…
-
I don't think that's silly, it's a matter of convention. Midi notes are numbers between 0-127 to have 12 note and 10 octave. In certain DAW they begin in c-2 in other DAW it isn't the case. Changing this in the firmware isn't hard but I think that w…
-
I don't think that's a software problem. But the LXR act differently if you connect a mono or stereo cable to the output. Perhaps, recheck the cable you'r using and the mixer config for each voice.
-
The LXR is more one instrument with 7 drum voices. Because they are "only" 16 channels in midi, a drum machine is often set to listen to one channel, and different notes of this channel are telling to the different voice to play. But the LXR is ver…
-
I will try to explain this shortly (and with my level in english) hope it will be clear. In midi there are different informations send from a software or an hardware and received by a software or an hardware. In your case Abelton send informations t…
-
I have check were was the setting. In voice mode then mix then totally on the right under NTE.
-
Good news your lxr receive midi. I m not in front of mine but in a menu there is certainly writen "any" that seem's that a voice react on any note of the selected channel. Change "any" to the note number you want. This setting is part of a kit so if…
-
I don't know ableton, but in my daw to send midi 36 I must play a C-3. Perhaps try to use every C note of all the octave you have in ableton. To see if your playing on the good octave.
-
Just an idea (i'm really not sure) but looking at this problem, I discovered that there are two type of sync in midi. One who transmit the midi clock and an other who transmit the start and stop (in the LXR manual "MIDI clock sync" and "MTC sync"). …
-
It never work correctly. The ribbon cable that i have received had the red strip on the "wrong" side. So when i connect it to the bus board with the red stripe on the bottom i think that the gate from the doepfer bus board was connected to the +12 o…
-
My last DIY experience was an LXR and I was waiting for the next one. I've never build an eurorack module before, I'm impatient to try. Thanks, It's very nice to begin the year with this.
-
I like the artwork too, there's a sort of continuity between this characters representing the machine and his function. Some speculation now, i'm thinking about (certainly cause i hope it since i've got the LXR with the trigger extension) a DIY midi…
-
My settings under (shift+save/load) are [bpm 0][qnt 32][ch 1][txf off][rxf all][mrt off][fch off][flw on][ssv on][pcr off][cki 1][co1 1][co2 4][mod off]. The reset in seems to work fine, but the LXR receive the clock from midi. Sorry havn't time tod…
-
I did a quick test of step recording from an external source (a DAW) sending note to LXR C-3 voice 1 C-3# voice 2 etc. on Chanel 1. The LXR record the step but i must select the voice for the step to be recorded perhaps cause they have all the same …
-
I agree with you, the note value thing isn't practical. If the hardware would be able to listen to voltage value, i would have convert the value in number of trig. 0.1 volt = x triggers, 0.2 volt = y triggers....but that doesn't seem to be possible.…
-
I was thinking that with the reset in this translation (high or low) could be used to say "high = addNote" and "low = erase note" and that the clock in was translating the number of high and low during a period of time and that we can use this value…
-
Just an idea to see if it would be possible to input notes value and record steps with the current hardware and any questions to see if i understand a bit the code and how it works.In the file TriggerOut.c changing{seq_setRunning(0); ---by seq_addNo…
-
I try it, and i can't hear any effect too, on sine and triangle wave. Your probably right cause the manual explain that: "The destination value is multiplied with the LFO value. That means the destination value is always modulated between its curren…
-
First of all, AAAAHHHH !!! The LXR with the trigger extension are so great :-)) thanks so much ! I wasn't hoping that the roll affect the trigger. I tripped so much in modulating a filter with an envelope and change the roll value in the same time. …
-
The analog 4 have a built in delay, reverb and chorus. (But no midi note out )
-
This year Christmas was earlier than the other years for me. When i finished building my LXR and all was working fine, it was like to open a wonderful present!!! So, thank you very much Julian and have a nice Christmas everyone.
-
If i'm not wrong... While you are in step mode => press a button from the sequencer to select a step => the selected step is blicking => the buttons AEG, MOD, FLT etc representes the substeps of the selected one => press them to activate…
-
Thanks for the explanations, So i made a few test with midi monitor on osx it's a bit like midi ox. The "…" are juste to replacing Clock. My DAW (renoise 2.8) slaved to an external midi sequencer via midi to usb 21:36:07.062 From Midi In 1 S…