pierre
About
- Username
- pierre
- Joined
- Visits
- 28
- Last Active
- Roles
- Member
Comments
-
Hi Julian, The four outputs are hooked up to a mixer, also receive usb midi from logic pro X, and send it throug the DIN to a XoXBoX. It's alright now, I think it might be fixed or might be intermittent. You probably don't remember but we did spent…
-
sorry for that unreadable post, the forum doesn't seem to work right with safari, the complete text is on another post, don't find how to delete this one.
-
Yep, everything works
-
Obviously, condenser not compresser
-
Alright, It works! First thing when I was debugging I've put the jumpers back the wrong way....shame...After that I was back to the start, so only L1 not working R1 have always been alright.Then I don't really know what happens Iwas playing with a w…
-
Any clue Julian?Thanks
-
Yeah in all honesty on my part I can live with that, I only really notice it on really round bass drums, and as mentioned before I think for one it's filter related. The manual states that it's a non linear phase filter so they'll always create some…
-
Actually it's not that, sorry by turning to zero the transient i realized I was mistaken, The sample there at 127 was just masking the attack and wasn't hearing the issue, but unfortunately it's a bit more random...
-
Sorry I didn't watch the video first you're right it does that here too but I think I found what it is, it's not the pitch of the drum, it's the transient Wav, when you chose something else than OFS it act normally here, I don't know what ofs stand …
-
And If it's relative to the cutoff, as you mention the Vel value is probably modulating the cutoff, but then it wouldn't change the pitch, but the tone, but for drum hits that are not really harmonically tuned that could be perceived as pitch change…
-
Those are settings for the voice, I'm still new experimenting with this DM but I think what takes care of the relative pitch between each step is the note parameter in the step editing If you do shift + hit on a step button, you see VEL then nte on…
-
So, sorry for the spamming, I sent info as they come and we can talk when you have more time but I did check the C26 capacity and I don't think there's any problems there. You can't get a precise mesure cause it would need to be taken out of the cir…
-
Also, from visual inspection I see a some chalky white stuff on C26, not sure what a leaking condenser should look like or the effect of that part, but might as well throw it here, just in case.
-
Also, just a tought, we may want to start looking at main boards inputs. Obviously analyzing data is not as straight forward as audio signal, but would you know of a specific path from the atmega that take care of routing/muting? any continuity chec…
-
So, the verdict is I don't have signal at any of those 3 points, (I definitely had it yesterday). Also, I don't know if it's expected, but removing all the jumpers the signal is still present on the stereo 2 outputs, no problem there. I confirm that…
-
ok thanks, I'll have to check that later,other work to do right now, actually I dont understand I think I just lost the right chan too, all of a sudden...
-
sorry you meanth the condenser, yes, there's signal at both legs
-
Yes there is signal at c20, the signal is on the Right pin, and if i insert the jumper it does transfer to left pin (the main board being top left, synth over under
-
Should I see signal from one of the jumper pins? if yes, which one?
-
I should have fought of that first but I do have a scope, no signal from the pins, normal behavior from all other signal pins so really there's nothing leaving the main board
-
As it is the same on every other outputs that work
-
I mesure 3.3 V on the switch pin, not 5 V
-
Yes, choosing L1 as an output have the same behavior as choosing stereo 1 and panning hard left, I loose my sound, so the firmware is behaving normally
-
so continuity check is right for everything Ground to Upper right, Lower right to the top two pins of the main board connector, no connectivity between signal pin and Ground/switch, and inserting a cable open the circuit between the top to pins of …
-
Sorry I was talking about the top to pin of the main board connector
-
..Haven't work, maybe the connector is faulty? hope it's not the main board, so basically any of the top two pin is signal right? With the wired that is attached to the upper left pin, I was hearing static in my speaker if i touch one of the two sig…
-
thanks I'll try that
-
they look alright
-
-
Well I might have been a little too enthusiastic. The L1 output doesn't work. This one could be harder, I tried a few different things but I might be confused so I see pin 28 and 38 from the main board. which one's on is tip and which one is sleeve?…